EL847 Series Photocoupler Datasheet - 16-Pin DIP Package - Isolation 5000Vrms - CTR 50-600% - English Technical Document

1. Product Overview

EL847 series yana wakiltar iyali na hanyoyin haɗin hoto na phototransistor guda huɗu da aka sanya a cikin daidaitaccen fakiti na Dual In-line Package (DIP) mai ƙugoshi goma sha shida. Kowane tashar tana haɗa diode mai fitar da infrared wanda aka haɗa ta hanyar gani zuwa na'urar ganowa ta phototransistor, yana samar da ƙaƙƙarfan keɓewar wutar lantarki tsakanin da'irorin shigarwa da fitarwa. An ƙera wannan na'urar don amintaccen watsa siginar a cikin yanayin da bambance-bambancen yuwuwar da juriyar amo suke da mahimmanci.

Babban aikin shine canja siginar lantarki ta amfani da haske, don haka samun keɓewar galvanic. Wannan yana hana madaukai na ƙasa, yana danne amo, da kuma kare da'irori masu hankali daga sauye-sauyen wutar lantarki mai girma. Jerin yana samuwa a cikin daidaitaccen hanyar rami ta DIP da zaɓuɓɓukan siffar jagora na saman-mount (SMD), yana ba da sassauci ga hanyoyin haɗa PCB daban-daban.

2. Zurfin Duba Sigogin Fasaha

2.1 Absolute Maximum Ratings

These ratings define the limits beyond which permanent damage to the device may occur. Operation under these conditions is not guaranteed.

• Input Forward Current (I_F): 60 mA (Continuous). This is the maximum DC current that can be applied to the input LED.
• Peak Forward Current (I_FP)1 A for 1 μs pulse. Allows for brief, high-current pulses for driving or testing.
• Reverse Voltage (V_R)6 V. The maximum reverse bias voltage the input LED can withstand.
• Collector-Emitter Voltage (V_CEO): 80 V. The maximum voltage the output phototransistor can block when off.
• Collector Current (I_C): 50 mA. The maximum continuous current the output transistor can sink.
• Isolation Voltage (V_ISO): 5000 V_rms for 1 minute. A key safety parameter indicating the dielectric strength between the input and output sides.
• Operating Temperature (T_OPR): -55°C to +110°C. Specifies the ambient temperature range for reliable operation.
• Soldering Temperature (T_SOL): 260°C for 10 seconds. Defines the reflow soldering profile tolerance.

2.2 Electro-Optical Characteristics

These parameters define the device's performance under normal operating conditions (T_A = 25°C unless noted).

2.2.1 Input Characteristics (LED Side)

• Forward Voltage (V_F): Typically 1.2V, maximum 1.4V at I_F = 20 mA. Used to calculate the required current-limiting resistor.
• Reverse Current (I_R): Maximum 10 μA at V_R = 4V. Indicates very low leakage when the LED is reverse-biased.
• Input Capacitance (C_in): Typically 30 pF, maximum 250 pF. Affects high-frequency switching capability on the input side.

2.2.2 Output Characteristics (Phototransistor Side)

• Collector-Emitter Dark Current (I_CEO): Maximum 100 nA at V_CE = 20V, I_F = 0mA. The leakage current when the LED is off; a lower value is better for noise immunity.
• Collector-Emitter Breakdown Voltage (BV_CEO): Minimum 80V at I_C = 0.1mA. E fa'amaonia ai le malosi o le poloka o le maualuga o le voltage.
• Collector-Emitter Saturation Voltage (V_CE(sat)): E masani lava 0.1V, maualuga 0.2V i le I_F = 20mA, I_C = 1mA. The voltage drop across the transistor when it is fully on (saturated). A low value is desirable to minimize power loss.

2.2.3 Transfer Characteristics

• Current Transfer Ratio (CTR): 50% to 600% at I_F = 5mA, V_CE = 5V. This is the most critical parameter, defined as (I_C / I_F) * 100%. It represents the efficiency of converting input current to output current. The wide range indicates the device is available in different gain bins.
• Isolation Resistance (R_IO): Minimum 5 x 10¹⁰ Ω at V_IO = 500V DC. Extremely high resistance between isolated sides, ensuring minimal leakage.
• Floating Capacitance (C_IO): Typically 0.6 pF, maximum 1.0 pF. The parasitic capacitance across the isolation barrier, which affects common-mode transient immunity and high-frequency noise coupling.
• Cut-off Frequency (f_c): Typically 80 kHz at V_CE = 5V, I_C = 2mA, R_L = 100Ω. The -3dB bandwidth, indicating the maximum useful digital signal frequency.
• Rise Time (t_r) & Fall Time (t_f): Typically 6 μs and 8 μs respectively (max 18 μs each) under specified test conditions. These switching speed parameters are crucial for determining maximum data rates in digital applications.

3. Performance Curve Analysis

The datasheet includes typical characteristic curves (though not detailed in the provided text). These would typically illustrate the relationship between key parameters, providing designers with a deeper understanding of device behavior beyond the tabulated min/typ/max values.

• CTR vs. Forward Current (I_F): Shows how efficiency changes with drive current, often peaking at a specific I_F.
• CTR vs. Temperature: Illustrates the negative temperature coefficient of CTR, which typically decreases as temperature increases. This is critical for designing stable circuits over the full temperature range.
• Output Current (I_C) vs. Collector-Emitter Voltage (V_CE): Family of curves showing the phototransistor's output characteristics for different input currents, similar to a bipolar transistor's output curves.
• Saturation Voltage (V_CE(sat)) vs. Collector Current (I_C)Yana nuna yadda ƙarar ƙarfin lantarki na yanayin kunna ke ƙaruwa tare da ƙarfin lodi.

4. Mechanical & Package Information

4.1 Girman Kunshin

The device is offered in two primary lead form options:

1. Standard DIP Type: Through-hole package with 16 pins on a 2.54mm (100-mil) pitch. Detailed dimensional drawings specify body length, width, height, pin length, and spacing.
2. Option S Type (Surface Mount): Gull-wing lead form for SMD assembly. Dimensions include footprint recommendations for PCB land pattern design.

A key safety-related mechanical feature is the creepage distance of >7.62 mm between the input and output sides of the package. This is the shortest distance along the surface of the insulating package between conductive parts and is essential for meeting safety standards for high isolation voltage.

4.2 Pinout and Schematic

The pin configuration is straightforward and consistent across channels:

• Pin 1, 3, 5, 7: Anode don Tashoshi 1-4 bi da bi.
• Pin 2, 4, 6, 8: Cathode don Tashoshi 1-4 bi da bi.
• Pins 9, 11, 13, 15: Emitter for Channels 1-4 respectively.
• Pins 10, 12, 14, 16: Collector for Channels 1-4 respectively.

This arrangement groups all inputs on one side (pins 1-8) and all outputs on the opposite side (pins 9-16), physically reinforcing the isolation barrier.

4.3 Device Marking

Devices are marked on the top with "EL847" (device number), followed by a 1-digit year code (Y), a 2-digit week code (WW), and an optional "V" suffix denoting VDE approval for that unit.

5. Soldering & Assembly Guidelines

5.1 Reflow Soldering Profile

The datasheet provides a detailed reflow profile compliant with IPC/JEDEC J-STD-020D for lead-free soldering:

• Dumama Kafin: 150°C zuwa 200°C a cikin dakika 60-120.
• Lokacin Sama da Liquidus (T_L=217°C): 60-100 seconds.
• Peak Temperature (T_P): 260°C maximum.
• Time within 5°C of Peak: 30 seconds maximum.
• Maximum Ramp-Up Rate: 3°C/second from T_smax to T_p.
• Maximum Ramp-Down Rate6°C/second.
• Total Cycle Time8 minutes maximum from 25°C to peak.
• Number of Reflows: The device can withstand up to 3 reflow cycles.

Adherence to this profile is critical to prevent package cracking, delamination, or damage to the internal die and wire bonds due to thermal stress.

6. Packaging & Ordering Information

The EL847 series is ordered using the part number format: EL847X-V.

• X: Lead form option. "S" for surface mount, blank (none) for standard DIP.
• V: Optional suffix indicating VDE safety approval is included for that specific unit.

Packing: Both variants are supplied in tubes containing 20 units each.

7. Application Suggestions

7.1 Typical Application Circuits

The EL847 is versatile and can be used in various configurations:

1. Digital Signal Isolation: Connect the input LED in series with a current-limiting resistor to a microcontroller GPIO pin. The output collector can be pulled up to the isolated side's logic voltage through a resistor. The emitter is typically grounded. This provides noise-immune transmission of ON/OFF signals, such as in PLC I/O modules.
2. Analog Signal Isolation (Linear Mode)By operating the phototransistor in its linear region (not saturated), the output current can be made roughly proportional to the input LED current. This requires careful biasing and is subject to CTR variations and temperature drift. It is often used for low-bandwidth, low-accuracy analog isolation.
3. Driving Small LoadsThe output can directly drive small loads like relays, LEDs, or optotriac drivers, provided the collector current and voltage ratings are not exceeded.

7.2 Design Considerations & Best Practices

• CTR Selection and Circuit Design: The wide CTR range (50-600%) necessitates careful design. For digital switching, choose a CTR bin that guarantees saturation of the output transistor at the minimum specified CTR with your chosen I_F and load resistor (R_L). The condition I_C = CTR_min * I_F must be greater than V_CC/R_L to ensure saturation.
• Speed vs. Current Trade-off: Higher I_F generally improves switching speed (reduces t_r/t_f) but decreases CTR over time due to LED aging. A design should use the lowest I_F that meets speed and noise immunity requirements.
• Noise Immunity and Bypassing: To improve common-mode transient immunity (CMTI), use a bypass capacitor (e.g., 0.1 μF) between the supply and ground on both the input and output sides, placed as close to the device pins as possible. This helps counteract the effects of the internal coupling capacitance (C_IO).
• Heat Dissipation: Observe the total power dissipation limits (P_TOT = 200 mW). Power is calculated as (I_F * V_F) on the input side plus (I_C * V_CE) on the output side.

8. Technical Comparison & Key Advantages

The EL847 differentiates itself in the market through several key features:

• High Isolation Voltage (5000 V_rms): Yana fi buƙatun yawancin aikace-aikacen sarrafa masana'antu da wadatar wutar lantarki, yana ba da babban gefen aminci.
• Faɗin Kewayon Yanayin Aiki (-55°C zuwa +110°C): Ya dace da mawuyacin yanayin masana'antu da na mota inda matsanancin zafi ya zama ruwan dare.
• Comprehensive Safety Approvals: UL, cUL, VDE, SEMKO, NEMKO, DEMKO, FIMKO, and CQC approvals simplify the process of incorporating the device into end products that require certification for various global markets.
• Four Channels in One Package: Offers board space savings and cost efficiency compared to using four single-channel optocouplers for multi-signal isolation tasks.
• Dual Package Options: Availability in both through-hole (DIP) and surface-mount (SMD) forms provides flexibility for both prototyping and high-volume automated assembly.

9. Frequently Asked Questions (Based on Technical Parameters)

Q1: How do I select the correct current-limiting resistor for the input LED?
A1: Use the formula: R_limit = (V_supply - V_F) / I_F. Use the maximum V_F from the datasheet (1.4V) for a worst-case design to ensure I_F is not exceeded. Choose I_F based on required CTR and speed; 5-20 mA is typical.

Q2: My circuit isn't switching fully. The output voltage doesn't go low enough. What's wrong?
A2: The phototransistor is likely not entering saturation. This is usually a CTR issue. Verify that your design uses the minimum CTR (50%) for calculations. Increase I_F or increase the value of the pull-up resistor R_L on the collector to reduce the required I_C for saturation (I_C(sat) ≈ V_CC/R_L).

Q3: Can I use this for isolating analog signals like sensor outputs?
A3: It is possible but challenging. The phototransistor's linearity is poor, and CTR varies significantly with temperature and device-to-device. For accurate analog isolation, dedicated isolation amplifiers or linear optocouplers (which include feedback to compensate for nonlinearities) are strongly recommended.

Q4: What is the significance of the creepage distance >7.62 mm?
A4: Creepage is the shortest path along the surface of the insulating package between conductive parts (e.g., input pin 1 and output pin 9). A longer creepage distance prevents surface tracking (arcing across the surface due to contamination or humidity) and is a mandatory requirement for safety certifications at high isolation voltages like 5000 V_rms.

10. Practical Design Case Study

Scenario: Isolating four digital control signals from a microcontroller to a 24V industrial actuator driver.

1. Requirements: Signal frequency < 1 kHz, high noise immunity, isolation for safety and ground loop prevention.
2. Design Choices:
   • Device: EL847 (Standard DIP).
   • Input Side: Microcontroller GPIO (3.3V, capable of 20mA). Choose I_F = 10 mA for good speed and longevity. R_limit = (3.3V - 1.4V) / 0.01A = 190Ω. Use a standard 200Ω resistor.
   • Output SideActuator driver expects a 24V logic high, pulled to ground for ON. Connect collector to 24V supply via a pull-up resistor. Choose R_L to ensure saturation at minimum CTR. Required I_C(sat) > 24V / R_L. With CTR_min=50% and I_F=10mA, I_C >= 5mA. Therefore, R_L must be < 24V / 0.005A = 4.8 kΩ. A 3.3 kΩ resistor is chosen, giving I_C(sat) ≈ 7.3mA, which is well within the device's 50mA rating and provides a good margin.
   • Bypassing: Add a 0.1 μF ceramic capacitor between Pin 10 (Collector 1) and Pin 9 (Emitter 1), and similarly for other channels, to improve noise immunity.
3. ResultInterface ya kwarin gwiwa, mai keɓancewar lantarki, mai iya watsa siginar sarrafawa cikin aminci a cikin yanayin masana'antu mai hayaniyar lantarki.

11. Ka'idar Aiki

Aikin photocoupler ya dogara ne akan jujjuyawar lantarki-optical-lantarki. Lokacin da aika wutar lantarki na gaba (I_F) aka yi amfani da shi ga shigarwar Infrared Emitting Diode (IRED), tana fitar da photons (haske) tare da tsawon raƙuman ruwa yawanci kusan 940 nm. Wannan hasken yana ratsa ta cikin tazarar keɓancewa mai gani (sau da yawa an yi shi da kayan gyare-gyare ko iska) a cikin kunshin. Hasken ya bugi yankin tushe na fitarwar silicon phototransistor. Photons ɗin da aka sha suna haifar da nau'i-nau'i na electron-ramu, suna haifar da wutar lantarki na tushe wanda ke kunna transistor, yana barin wutar lantarki mai tattarawa (I_C) to flow. The key point is that the only connection between the input and output is the beam of light, providing the galvanic isolation. The ratio I_C/I_F is the Current Transfer Ratio (CTR), which depends on the LED's luminous efficiency, the phototransistor's sensitivity, and the optical coupling efficiency between them.

12. Industry Trends & Context

EL847 irin awọn photocouplers tun jẹ awọn ẹya pataki ni agbara itanna, iṣẹ-ṣiṣe ọna iṣowo, ati awọn eto agbara imudara nibi ti iyasọtọ agbara giga jẹ alaileṣe. Itọsọna ni ẹka yii wa si:

• Iyara Giga: Iṣelọpọ awọn iyasọtọ oni-nọmba ti o da lori CMOS RF tabi awọn imọ-ẹrọ ibatan capacitive ti o nfunni ni awọn iwọn data ni Mbps si Gbps, ti o kọja pupọ awọn opin ~100 kHz ti awọn atukọsi fototransistor atijọ.
• Higher Integration Combining isolation with other functions like gate drivers, ADC interfaces, or USB/I2C/SPI isolators in single packages.
• Improved Reliability & Lifetime: Focus on LED technology with lower degradation over time and temperature, leading to more stable CTR over the product's lifetime.
• Miniaturization: Moving towards smaller, surface-mount packages like SOIC-8 and even smaller, while maintaining or improving isolation ratings.

Despite these trends, phototransistor-based photocouplers maintain strong relevance due to their simplicity, robustness, high isolation voltage capability, ease of use, and cost-effectiveness for applications requiring medium-to-low speed signal isolation, such as the programmable controllers, home appliances, and telecommunication equipment listed in the EL847 datasheet. Their comprehensive safety certifications make them a trusted choice for designs requiring regulatory approval.